Apple

 
 

  
 
 


Our Price: £126.08 (£107.37 ex Vat.)

Item Number: 553759

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: Brodit Brand New Item - PreOrder Yours NOW !

Active Car Cradle Mount with cig-plug and USB cable. With tilt swivel. With spring stud locking. For OtterBox Defender Series.

This Car Cradle Mount is to be used when you want to have your iPad extra securely in place and still have it easy accessable. The Car Cradle Mount is equipped with a cig-plug for connection to the vehicle's 12 Volt socket so you will always have a freshly charged battery!

The Car Cradle Mount is made of extra strong plastic and is equipped with a spring stud locking device. The Car Cradle Mount is mounted onto a tilt swivel. This mean that you can adjust the angle in order to avoid light reflection on the screen. You can easily switch between portrait and landscape mode by turning the Car Cradle Mount into desired position.

Tablets (Surfpads) should not be installed onto a car's dashboard if they block the view or block key controls. Proclip Car Bracket Mount (Brodit's vehicle mounting bracket) is designed for installation of smaller devices like Apple iPad Air 2 phones and GPS devices, Proclip Car Bracket Mount is not designed for large devices like tablets. In some vehicles the Proclip Car Bracket Mount has an extra firm fit and can then be used also for installation of a tablet. If you want to place a tablet onto the car's dashboard, each combination of tablet-car must be examined in detail by you in order to determine if such an installation is possible in the specific case. Consideration should be given to the position and how firmly the Proclip Car Bracket Mount is in place, as well as the size of the tablet you wish to use. Brodit will not give any recommendations for such installations.

An installation of a tablet onto a vehicle's dashboard is always done on the customer's own responsibility. Brodit recommends to use tablets on the car's headrest, installed onto a Brodit headrest mount.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Apple iPad Air 2 MP3 Player. This is how you fit your Car Cradle Mount for Locking mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Car Cradle Mount.



Enlarge image

1. Loosen the screw in the center of the Car Cradle Mount so you can remove the tilt swivel attaching plate on the back. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. Place the Car Cradle Mount over the attaching plate so the screw fits in the hole in the tilt swivel. Screw the Car Cradle Mount onto the attaching plate. Tighten the screw so the Car Cradle Mount is firmly in place, but still can be adjusted.



Enlarge image

2. Slide the device sideways carefully into the Car Cradle Mount until you feel that it is properly attached to the connector. Press the spring stud locking device sideways onto the left part of the Car Cradle Mount.




Enlarge image

3. Remove the spring stud locking device by slidning it sideways away from the Car Cradle Mount. Slide the device sideways carefully out of the Car Cradle Mount.



Enlarge image

4. The Car Cradle Mount is in place. Switch between portrait and landscape mode by turning the Car Cradle Mount into desired position.







Apple iPad Air 2 for All Countries






Our Price: £126.08 (£107.37 ex Vat.)

Item Number: 552759

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: Brodit Brand New Item - PreOrder Yours NOW !

Active Car Cradle Mount with cig-plug and USB cable. With tilt swivel. 2 keys included. For OtterBox Defender Series.

This Car Cradle Mount is to be used when you will secure your iPad and still have it easy accessable. Perfect for use in stores, at exhibitions and any place where you want to use your iPad without having it easy removable. In order to remove the unit from the Car Cradle Mount you need the key or a certain amount of violence is required. The Car Cradle Mount includes a lock and two keys.

The active Car Cradle Mount charges your battery when it is in the Car Cradle Mount. The Car Cradle Mount is attached onto a tilt swivel and can be adjusted in order to avoid light reflection. Connects to the vehicle's cigarette lighter socket, 12/24 Volt.

Tablets (Surfpads) should not be installed onto a car's dashboard if they block the view or block key controls. Proclip Car Bracket Mount (Brodit's vehicle mounting bracket) is designed for installation of smaller devices like Apple iPad Air 2 phones and GPS devices, Proclip Car Bracket Mount is not designed for large devices like tablets. In some vehicles the Proclip Car Bracket Mount has an extra firm fit and can then be used also for installation of a tablet. If you want to place a tablet onto the car's dashboard, each combination of tablet-car must be examined in detail by you in order to determine if such an installation is possible in the specific case. Consideration should be given to the position and how firmly the Proclip Car Bracket Mount is in place, as well as the size of the tablet you wish to use. Brodit will not give any recommendations for such installations.

An installation of a tablet onto a vehicle's dashboard is always done on the customer's own responsibility. Brodit recommends to use tablets on the car's headrest, installed onto a Brodit headrest mount.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Apple iPad Air 2 MP3 Player. This is how you fit your Car Cradle Mount with lock. mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Car Cradle Mount.



Enlarge image

1. Loosen the screw in the center of the Car Cradle Mount so you can remove the tilt swivel attaching plate on the back. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. Place the Car Cradle Mount over the attaching plate so the screw fits in the hole in the tilt swivel. Screw the Car Cradle Mount onto the attaching plate. Tighten the screw so the Car Cradle Mount is firmly in place, but still can be adjusted.



Enlarge image

2. Slide the device sideways carefully into the Car Cradle Mount. Press the lock sideways onto the left part of the Car Cradle Mount. Press the button to lock.




Enlarge image

3. Use the enclosed key to open the lock. Remove the lock by slidning it sideways away from the Car Cradle Mount. Slide the device sideways carefully out of the Car Cradle Mount.



Enlarge image

4. The Car Cradle Mount is in place. Switch between portrait and landscape mode by turning the Car Cradle Mount into desired position.







Apple iPad Air 2 for All Countries






Our Price: £145.48 (£123.89 ex Vat.)

Item Number: 547759

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: Brodit Brand New Item - PreOrder Yours NOW !

Active Car Cradle Mount for fixed installation. With tilt swivel. With spring stud locking. For OtterBox Defender Series.

This Car Cradle Mount is to be used when you want to have your iPad extra securely in place and still have it easy accessable. The active Car Cradle Mount is to be connected inside the dashboard. It provides a discreet and neat installation without any cables hanging over the interior. Safe and convenient!

12 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. Professional installation recommended.

The Car Cradle Mount is made of extra strong plastic and is equipped with a spring stud locking device. The Car Cradle Mount is mounted onto a tilt swivel. This mean that you can adjust the angle in order to avoid light reflection on the screen. You can easily switch between portrait and landscape mode by turning the Car Cradle Mount into desired position.

Tablets should not be installed onto a car's dashboard if blocking the view or key controls. Proclip Car Bracket Mount is designed for use with smaller devices like smartphones. If you want to place a tablet onto a dashboard, each combination of tablet-car must be examined in detail by yourself in order to determine if such an installation is possible in the specific case. Brodit will not give any recommendations for such installations. An installation of a tablet onto a vehicle's dashboard is always done on the customer's own responsibility. Brodit recommends using tablets on the car's headrest, installed onto a Brodit headrest mount.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Apple iPad Air 2 MP3 Player. This is how you fit your Car Cradle Mount for Locking mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Car Cradle Mount. The charger unit is fused internally with 2 A automotive re-settable thermal fuse, but if an external fuse is to be installed then connect a 2 A fuse Car Cradle Mount and fuse inline with the Red wire close to the power source. Route the cable from the Car Cradle Mount into the vehicle dashboard and secure the charger unit in place with the adhesive tape provided. Ensure the charger unit is securely mounted behind the dashboard in a well ventilated area that does not get hot! If you are connecting a GPS/Data device to the Car Cradle Mount please ensure the charger unit is located in a position within easy reach of any GPS or charging adapters. Route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle. Mount Car Cradle Mount: 1. Loosen the screw in the center of the Car Cradle Mount and remove the tilt swivel attaching plate on the back. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. Place the Car Cradle Mount over the attaching plate so the screw fits in the tilt swivel. Screw the Car Cradle Mount onto the attaching plate. Tighten the screw so the Car Cradle Mount is firmly in place, but still can be adjusted. 2. Slide the device sideways carefully into the Car Cradle Mount until you feel that it is properly attached to the connector. Press the spring stud locking device sideways onto the left part of the Car Cradle Mount. 3. Slide the spring stud locking device sideways away and out of the Car Cradle Mount.4. The Car Cradle Mount is in place. Switch between portrait and landscape mode by turning the Car Cradle Mount into desired position.







Apple iPad Air 2 for All Countries






Our Price: £145.48 (£123.89 ex Vat.)

Item Number: 536759

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: Brodit Brand New Item - PreOrder Yours NOW !

Active Car Cradle Mount for fixed installation. With tilt swivel. 2 keys included. For OtterBox Defender Series.

This Car Cradle Mount is to be used when you will secure your iPad and still have it easy accessable. Perfect for use in stores, at exhibitions and any place where you want to use your iPad without having it easy removable. In order to remove the unit †from the Car Cradle Mount you need the key or a certain amount of violence is required. The Car Cradle Mount includes a lock and two keys.

Keep your device in an active Car Cradle Mount while on the road, and you will always have a freshly charged battery! The active Car Cradle Mount is to be connected inside the dashboard, this gives a discreet, neat installation without cables hanging over the interior!

12 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. †Professional installation recommended. The Car Cradle Mount is attached onto a tilt swivel so you can easily adjust your device in order to avoid light reflection.

Tablets should not be installed onto a car's dashboard if blocking the view or key controls. Proclip Car Bracket Mount is designed for use with smaller devices like smartphones. If you want to place a tablet onto a dashboard, each combination of tablet-car must be examined in detail by yourself in order to determine if such an installation is possible in the specific case. Brodit will not give any recommendations for such installations. An installation of a tablet onto a vehicle's dashboard is always done on the customer's own responsibility. Brodit recommends using tablets on the car's headrest, installed onto a Brodit headrest mount.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Apple iPad Air 2 MP3 Player. This is how you fit your Car Cradle Mount with lock. mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Car Cradle Mount. The charger unit is fused internally with 2 A automotive re-settable thermal fuse, but if an external fuse is to be installed then connect a 2 A fuse Car Cradle Mount and fuse inline with the Red wire close to the power source. Route the cable from the Car Cradle Mount into the vehicle dashboard and secure the charger unit in place with the adhesive tape provided. Ensure the charger unit is securely mounted behind the dashboard in a well ventilated area that does not get hot! If you are connecting a GPS/Data device to the Car Cradle Mount please ensure the charger unit is located in a position within easy reach of any GPS or charging adapters. Route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle. Mount Car Cradle Mount: 1. Loosen the screw in the center of the Car Cradle Mount so you can remove the tilt swivel attaching plate on the back. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. Place the Car Cradle Mount over the attaching plate so the screw fits in the hole in the tilt swivel. Screw the Car Cradle Mount onto the attaching plate. Tighten the screw so the Car Cradle Mount is firmly in place, but still can be adjusted. 2. Slide the device sideways carefully into the Car Cradle Mount. Press the lock sideways onto the left part of the Car Cradle Mount. Press the button to lock. 3. Use the enclosed key to open the lock. Remove the lock by slidning it sideways away from the Car Cradle Mount. Slide the device sideways carefully out of the Car Cradle Mount. 4. The Car Cradle Mount is in place. Switch between portrait and landscape mode by turning the Car Cradle Mount into desired position.







Apple iPad Air 2 for All Countries






Our Price: £49.46 (£42.12 ex Vat.)

Item Number: 541759

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: Brodit Brand New Item - PreOrder Yours NOW !

Passive Car Cradle Mount with tilt swivel. With spring stud locking. For device with Otterbox Defender Series case.

This Car Cradle Mount is to be used when you want to have your iPad extra securely in place and still have it easy accessable.

The Car Cradle Mount is made of extra strong plastic and is equipped with a spring stud locking device. The Car Cradle Mount is mounted onto a tilt swivel. This mean that you can adjust the angle in order to avoid light reflection on the screen. You can easily switch between portrait and landscape mode by turning the Car Cradle Mount into desired position.

Tablets (Surfpads) should not be installed onto a car's dashboard if they block the view or block key controls. Proclip Car Bracket Mount (Brodit's vehicle mounting bracket) is designed for installation of smaller devices like Apple iPad Air 2 phones and GPS devices, Proclip Car Bracket Mount is not designed for large devices like tablets. In some vehicles the Proclip Car Bracket Mount has an extra firm fit and can then be used also for installation of a tablet. If you want to place a tablet onto the car's dashboard, each combination of tablet-car must be examined in detail by you in order to determine if such an installation is possible in the specific case. Consideration should be given to the position and how firmly the Proclip Car Bracket Mount is in place, as well as the size of the tablet you wish to use. Brodit will not give any recommendations for such installations.

An installation of a tablet onto a vehicle's dashboard is always done on the customer's own responsibility. Brodit recommends to use tablets on the car's headrest, installed onto a Brodit headrest mount.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Apple iPad Air 2 MP3 Player. This is how you fit your Car Cradle Mount for Locking mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Car Cradle Mount.



Enlarge image

1. Loosen the screw in the center of the Car Cradle Mount so you can remove the tilt swivel attaching plate on the back. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. Place the Car Cradle Mount over the attaching plate so the screw fits in the hole in the tilt swivel. Screw the Car Cradle Mount onto the attaching plate. Tighten the screw so the Car Cradle Mount is firmly in place, but still can be adjusted.



Enlarge image

2. Slide the device sideways carefully into the Car Cradle Mount. Press the spring stud locking device sideways onto the left part of the Car Cradle Mount.




Enlarge image

3. Remove the spring stud locking device by slidning it sideways away from the Car Cradle Mount. Slide the device sideways carefully out of the Car Cradle Mount.



Enlarge image

4. The Car Cradle Mount is in place. Switch between portrait and landscape mode by turning the Car Cradle Mount into desired position.







Apple iPad Air 2 for All Countries






 

 



Thank you for adding your Brodit Car Cradle Mount. The Brodit Solution involves Two Steps. If you require a Brodit Car Bracket Mount then please select from the menus below. If you already have a Brodit Car Bracket Mount please proceed to checkout.