Honeywell

 
 

  
 
 


Our Price: 24.71 (21.04 ex Vat.)

Item Number: 511292

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: 4

With your Honeywell Dolphin 6000 in a passive Car Cradle Mount attached onto the dashboard it is always within easy reach -safe and convenient. The Car Cradle Mount is mounted onto a tilt swivel so it is adjustable for avoiding light reflection on the screen. It is easy to put the Honeywell Dolphin 6000 in the Car Cradle Mount, and to take it out of the Car Cradle Mount. You can connect e.g. a charging cable to the Honeywell Dolphin 6000 when it is in the Car Cradle Mount.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Honeywell Dolphin 6000 PDA. This is how you fit your Passive Car Cradle Mount with tilt swivel mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Car Cradle Mount.



Enlarge image

1. Loosen the screw in the center of the Car Cradle Mount so you can remove the tilt swivel attaching plate on the back.



Enlarge image

2. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. Place the Car Cradle Mount over the attaching plate so the screw fits in the hole in the tilt swivel. Tighten the screw so the Car Cradle Mount is firmly in place, but still can be adjusted.




Enlarge image

3. To place the device in the Car Cradle Mount: Place the bottom part of the device into the Car Cradle Mount. Press the top of the device forward and in the same time slide the device downward into place in the Car Cradle Mount. To remove the device from the Car Cradle Mount: Press the upper part of the Car Cradle Mount forward. When the device is set free, lift it upward out of the Car Cradle Mount.



Enlarge image

4. The Car Cradle Mount is in place.







Honeywell Dolphin 6000 for All Countries






Our Price: 71.28 (60.70 ex Vat.)

Item Number: 513292

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: Brodit Brand New Item - PreOrder Yours NOW !

With tilt swivel, with Molex adapter system. 2A charger.

An active Car Cradle Mount which is to be connected inside the dashboard, this gives a discreet, neat installation without cables hanging over the interior!

You can choose to use the Car Cradle Mount as an active Car Cradle Mount for charging of your device only, or to connect an adapter to the Molex connector for additional features. Then you can use the Car Cradle Mount also for power supply of a GPS receiver or other own solutions (can not be used for data communication or audio connection).

12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. Professional installation recommended. The Car Cradle Mount is attached onto a tilt swivel so you can easily adjust your device in order to avoid light reflection. Attach onto a Proclip Car Bracket Mount Mounting Platform.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Honeywell Dolphin 6000 PDA. This is how you fit your Active Car Cradle Mount for fixed installation. mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Car Cradle Mount. Important Note: Route the cable from the Car Cradle Mount into the vehicle dashboard and route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle.



Enlarge image

1. Loosen the screw in the center of the Car Cradle Mount so you can remove the tilt swivel attaching plate on the back.



Enlarge image

2. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. Place the Car Cradle Mount over the attaching plate so the screw fits in the hole in the tilt swivel. Tighten the screw until the Car Cradle Mount is firmly in place, but still can be adjusted.




Enlarge image

3. To place the device in the Car Cradle Mount: Place the botto part of the device into the Car Cradle Mount. Slide the device downward into place in the Car Cradle Mount. To remove the device fron the Car Cradle Mount: Open the latch on the Car Cradle Mount. Then the device is set free, lift it upward out of the Car Cradle Mount.



Enlarge image

4. The Car Cradle Mount is in place.







Honeywell Dolphin 6000 for All Countries






Our Price: 71.28 (60.70 ex Vat.)

Item Number: 512292

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: Stock on Order - delivery approx. 7-10 days

With tilt swivel.

The active Car Cradle Mount charges your battery when it is in the Car Cradle Mount. The charging device connects to the Honeywell Dolphin 6000 automatically when you put the Honeywell Dolphin 6000 in the Car Cradle Mount. The Car Cradle Mount is attached onto a tilt swivel and can be adjusted in order to avoid light reflection. Connects to the vehicle's cigarette lighter socket, 12/24 Volt. Attach onto a Proclip Car Bracket Mount Mounting Platform.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Honeywell Dolphin 6000 PDA. This is how you fit your Active Car Cradle Mount with cig-plug. mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Car Cradle Mount.



Enlarge image

1. Loosen the screw in the center of the Car Cradle Mount so you can remove the tilt swivel attaching plate on the back.



Enlarge image

2. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. Place the Car Cradle Mount over the attaching plate so the screw fits in the hole in the tilt swivel. Tighten the screw so the Car Cradle Mount is firmly in place, but still can be adjusted.




Enlarge image

3. To place the device in the Car Cradle Mount: Place the bottom part of the device into the Car Cradle Mount. Press the top of the device forward and in the same time slide the device downward into place in the Car Cradle Mount. To remove the device from the Car Cradle Mount: Press the upper part of the Car Cradle Mount forward. When the device is set free, lift it upward out of the Car Cradle Mount.



Enlarge image

4. The Car Cradle Mount is in place.







Honeywell Dolphin 6000 for All Countries






 

 



Thank you for adding your Brodit Car Cradle Mount. The Brodit Solution involves Two Steps. If you require a Brodit Car Bracket Mount then please select from the menus below. If you already have a Brodit Car Bracket Mount please proceed to checkout.