Motorola

 
 

  
 
 


Our Price: £71.28 (£60.70 ex Vat.)

Item Number: 513707

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: Brodit Brand New Item - PreOrder Yours NOW !

With tilt swivel, with Molex adapter system. 2A charger.

An active Car Cradle Mount which is to be connected inside the dashboard, this gives a discreet, neat installation without cables hanging over the interior!
 
You can choose to use the Car Cradle Mount as an active Car Cradle Mount for charging of your device only, or to connect an adapter to the Molex connector for additional features. Then you can use the Car Cradle Mount also for power supply of a GPS receiver or other own solutions (can not be used for data communication or audio connection).
 
12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger.  Professional installation recommended. The Car Cradle Mount is attached onto a tilt swivel so you can easily adjust your device in order to avoid light reflection. Attach onto a Proclip Car Bracket Mount Mounting Platform.
 
Charging specifications:
Input voltage: DC/10-30V
Charging voltage: DC/4.75-5.3V
Output current(Typ): 2.0A
Input & output protection: Input polarity reversal/Output over voltage/Output over current/Output short protection
LED charging indicator: Power input indicator(Green), Ovp/Ocp/Output short(Red)
Operating temperature: 0°C ~ +40°C
Storage temperature: -20°C ~ +80°C
RoHS compliant: ROHS


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Motorola TC70 PDA. This is how you fit your Active Car Cradle Mount for fixed installation mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Car Cradle Mount. Important Note: Route the cable from the Car Cradle Mount into the vehicle dashboard and route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle.  



Enlarge image

1. Loosen the screw in the center of the Car Cradle Mount so you can remove the tilt swivel attaching plate on the back.



Enlarge image

2. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. Place the Car Cradle Mount over the attaching plate so the screw fits in the hole in the tilt swivel. Tighten the screw until the Car Cradle Mount is firmly in place, but still can be adjusted.




Enlarge image

3. To place the device in the Car Cradle Mount: Place the bottom part of the device into the Car Cradle Mount. Press the top of the device forward and in the same time slide the device downward into place in the Car Cradle Mount. To remove the device from the Car Cradle Mount: Press the upper part of the Car Cradle Mount forward. When the device is set free, lift it upward out of the Car Cradle Mount.



Enlarge image

4. The Car Cradle Mount is in place.







Motorola TC70 for All Countries
Motorola TC75 for All Countries

Symbol TC70 for All Countries
Symbol TC75 for All Countries

Zebra TC70 for All Countries
Zebra TC75 for All Countries






 

 



Thank you for adding your Brodit Car Cradle Mount. The Brodit Solution involves Two Steps. If you require a Brodit Car Bracket Mount then please select from the menus below. If you already have a Brodit Car Bracket Mount please proceed to checkout.