Fiat

 
 

 
 
 


Our Price: 15.20 (12.94 ex Vat.)

Item Number: 653973

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: 2

The Proclip Car Bracket Mount is a mounting bracket for the Fiat Scudo's dashboard. Onto the Proclip Car Bracket Mount you can install e.g. a Car Cradle Mount for your mobile phone or PDA or a handsfree set etc. Safe and convenient -always within easy reach. The Proclip Car Bracket Mount is car specific and easy to install. The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the Fiat Scudo. Made in black ABS plastic. Comes with detailed instructions.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Fiat Scudo Vehicles. This is how you fit your Proclip Car Bracket Mount mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Proclip Car Bracket Mount.



Enlarge image

1. Open the glove compartment. Remove the screw in the upper right corner. Press the thin end of the enclosed gap opener into the gap between the frame surrounding the control panel and the dashboard, to widen the gap. Peel off the cover of the adhesive tape on the Proclip Car Bracket Mount.



Enlarge image

2. Press the curved edge on the right part of the Proclip Car Bracket Mount into the gap below the gap opener. Flip the Proclip Car Bracket Mount forward/leftward so the curved right edge hooks behind the frame surrounding the control panel




Enlarge image

3. Adjust the left part of the Proclip Car Bracket Mount so the hole matches the hole in the dashboard. Screw the Proclip Car Bracket Mount into place with the enclosed screw. Pull out the gap opener. Close the glove compartment.



Enlarge image

4. The Proclip Car Bracket Mount is in place.







Citroen Dispatch for UK
Citroen Jumpy 2nd Gen for UK
Citroen Jumpy III for UK

Fiat Scudo for UK

Peugeot Expert for All Countries

Toyota ProAce for All Countries






Our Price: 15.20 (12.94 ex Vat.)

Item Number: 653972

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: 5

The Proclip Car Bracket Mount is a mounting bracket for the Fiat Scudo's dashboard. Onto the Proclip Car Bracket Mount you can install e.g. a Car Cradle Mount for your mobile phone or PDA or a handsfree set etc. Safe and convenient -always within easy reach. The Proclip Car Bracket Mount is car specific and easy to install. The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the Fiat Scudo. Made in black ABS plastic. Comes with detailed instructions.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Fiat Scudo Vehicles. This is how you fit your Proclip Car Bracket Mount mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Proclip Car Bracket Mount. It is very important to place the Proclip Car Bracket Mount in the exact same position as shown in the pictures.



Enlarge image

1. Press the thin end of the enclosed gap openers into the gap between the frame surrounding the air vent and the coin compartment, to widen the gap. Peel off the adhesive tape covers on the Proclip Car Bracket Mount.



Enlarge image

2. Press the angled edge on the upper part of the Proclip Car Bracket Mount into the gap between the gap openers.




Enlarge image

3. Pull the Proclip Car Bracket Mount downward and press the lower part foward so the angled edge hooks into the gap between the frame surrounding the stereo and the frame surrounding the air vent. Pull out the gap openers.



Enlarge image

4. The Proclip Car Bracket Mount is in place.







Citroen Dispatch for UK
Citroen Jumpy 2nd Gen for UK
Citroen Jumpy III for UK

Fiat Scudo for UK

Peugeot Expert for All Countries

Toyota ProAce for All Countries






Our Price: 15.20 (12.94 ex Vat.)

Item Number: 603974

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: Stock on Order - delivery approx. 7-10 days

Will block cup Car Cradle Mount.

The Proclip Car Bracket Mount is a mounting bracket for the Fiat Scudo's dashboard. Onto the Proclip Car Bracket Mount you can install e.g. a Car Cradle Mount for your mobile phone or PDA or a handsfree set etc. Safe and convenient -always within easy reach. The Proclip Car Bracket Mount is car specific and easy to install. The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the Fiat Scudo. Made in black ABS plastic. Comes with detailed instructions.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Fiat Scudo Vehicles. This is how you fit your Proclip Car Bracket Mount mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Proclip Car Bracket Mount. It is important to place the Proclip Car Bracket Mount in the exact same position as shown in the pictures.



Enlarge image

1. Press the grooved edge on the lower part of the Proclip Car Bracket Mount into the gap between the frame surrounding the air vent and the dashboard. Press until you hear/feel it snaps into place.



Enlarge image

2. Press the thin end of the enclosed gap opener into the gap between the frame surrounding the air vent and the dashboard, to widen the gap. Press forward on the upper part of the Proclip Car Bracket Mount so the grooved edge goes into the gap next to the gap opener. Press until you hear/feel it snaps into place. If the gap is very tight, carefully use the gap opener to bend it a bit wider. Pull out the gap opener.




Enlarge image

3. Press forward on the Proclip Car Bracket Mount so it is properly in place.



Enlarge image

4. The Proclip Car Bracket Mount is in place.







Citroen Dispatch for UK
Citroen Jumpy 2nd Gen for UK
Citroen Jumpy III for UK

Fiat Scudo for UK

Peugeot Expert for All Countries

Toyota ProAce for All Countries






Brodit ProClip for Fiat Scudo Left Car Bracket Mount #804998

Citroen Jumpy 2nd Gen Europe / Citroen Jumpy III Europe / Fiat Scudo All Countries / Peugeot Expert All Countries / Toyota ProAce Europe

Our Price: 15.50 (13.20 ex Vat.)

Item Number: 804998

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: Brodit Brand New Item - PreOrder Yours NOW !

The Proclip Car Bracket Mount is a mounting bracket for the Fiat Scudo's dashboard. Onto the Proclip Car Bracket Mount you can install e.g. a Car Cradle Mount for your mobile phone or PDA or a handsfree set etc. Safe and convenient - always within easy reach. The Proclip Car Bracket Mount is car specific and easy to install. The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the Fiat Scudo. Made in black ABS plastic. Comes with detailed instructions.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Fiat Scudo Vehicles. This is how you fit your Proclip Car Bracket Mount mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Proclip Car Bracket Mount.



Enlarge image

1. Use the enclosed alcohol pad to clean the area where the Proclip Car Bracket Mount is to be installed. Pull out the rubber sealent on the A-post slightly. Remove the adhesive tape covers on the Proclip Car Bracket Mount.



Enlarge image

2. Press the angled edge on the lower part of the Proclip Car Bracket Mount into the gap and hook it around the A-post.




Enlarge image

3. Press the Proclip Car Bracket Mount upward/forward so the angled upper edge hooks around the A-post.



Enlarge image

4. The Proclip Car Bracket Mount is in place.







Citroen Jumpy 2nd Gen for Europe
Citroen Jumpy III for Europe

Fiat Scudo for All Countries

Peugeot Expert for All Countries

Toyota ProAce for Europe






Brodit ProClip for Fiat Scudo Right Car Bracket Mount #604998

Citroen Jumpy 2nd Gen UK / Citroen Jumpy III UK / Fiat Scudo UK / Peugeot Expert UK / Toyota ProAce All Countries

Our Price: 15.20 (12.94 ex Vat.)

Item Number: 604998

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: Stock on Order - delivery approx. 7-10 days

The Proclip Car Bracket Mount is a mounting bracket for the Fiat Scudo's dashboard. Onto the Proclip Car Bracket Mount you can install e.g. a Car Cradle Mount for your mobile phone or PDA or a handsfree set etc. Safe and convenient - always within easy reach. The Proclip Car Bracket Mount is car specific and easy to install. The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the Fiat Scudo. Made in black ABS plastic. Comes with detailed instructions.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Fiat Scudo Vehicles. This is how you fit your Proclip Car Bracket Mount mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Proclip Car Bracket Mount.



Enlarge image

1. Use the enclosed alcohol pad to clean the area where the Proclip Car Bracket Mount is to be installed. Pull out the rubber sealent on the A-post slightly. Remove the adhesive tape cover on the Proclip Car Bracket Mount.



Enlarge image

2. Press the angled edge on the lower part of the Proclip Car Bracket Mount into the gap and hook it around the A-post.




Enlarge image

3. Press the Proclip Car Bracket Mount upward/forward so the angled upper edge hooks around the A-post.



Enlarge image

4. The Proclip Car Bracket Mount is in place.







Citroen Jumpy 2nd Gen for UK
Citroen Jumpy III for UK

Fiat Scudo for UK

Peugeot Expert for UK

Toyota ProAce for All Countries






 

 



Thank you for adding your Brodit Car Bracket Mount. The Brodit Solution involves Two Steps. If you require a Brodit Car Cradle Mount then please select from the menus below. If you already have a Brodit Car Cradle Mount please proceed to checkout.