Toyota

 
 

 
 
 


Brodit ProClip for Toyota LandCruiser 120 Angled Car Bracket Mount #653197

Toyota LandCruiser UK / Toyota LandCruiser 120 All Countries / Toyota Prado Australia

Our Price: 15.20 (12.94 ex Vat.)

Item Number: 653197

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: Brodit Brand New Item - PreOrder Yours NOW !

The Proclip Car Bracket Mount is a mounting bracket for the Toyota LandCruiser 120's dashboard. Onto the Proclip Car Bracket Mount you can install e.g. a Car Cradle Mount for your mobile phone or PDA or a handsfree set etc. Safe and convenient -always within easy reach. The Proclip Car Bracket Mount is car specific and easy to install. The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the Toyota LandCruiser 120. Made in black ABS plastic. Comes with detailed instructions.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Toyota LandCruiser 120 Vehicles. This is how you fit your Proclip Car Bracket Mount mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Attention! Please read all of the instructions and look at the pictures before attaching the Proclip Car Bracket Mount. This Proclip Car Bracket Mount consists of two parts. Part 1. Attaching part (the smallest part) Part 2. Proclip Car Bracket Mount face plate



Enlarge image

1. Press the thin end of the enclosed gap opener into the gap between the wood grain panel and the padded dashboard, to widen the gap.



Enlarge image

2. Peel off the cover of the adhesive tape on Part 1. Place the angled edge of Part 1 towards the gap below the gap opener. Press the angled edge firmly into the gap and at the same time: bend Part 1 to the left until you hear/feel it snaps into place and the adhesive tape attaches to the console edge. Pull out the gap opener.




Enlarge image

3. Press a screwdriver (Philips) firmly through the predrilled holes in Part 2 to open them up. Peel off the cover of the adhesive tape on Part 2. Place Part 2 onto Part 1 so the holes match and the adhesive tape on Part 2 is on the right side attaching to the center console panel frame. Screw Part 2 onto Part 1 using the enclosed screws. NOTE! Screw straight into Part 1, in the same anlge as Part 1.



Enlarge image

4. The Proclip Car Bracket Mount is in place.







Toyota LandCruiser for UK
Toyota LandCruiser 120 for All Countries
Toyota Prado for Australia






Our Price: 15.20 (12.94 ex Vat.)

Item Number: 653973

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: 2

The Proclip Car Bracket Mount is a mounting bracket for the Toyota ProAce's dashboard. Onto the Proclip Car Bracket Mount you can install e.g. a Car Cradle Mount for your mobile phone or PDA or a handsfree set etc. Safe and convenient -always within easy reach. The Proclip Car Bracket Mount is car specific and easy to install. The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the Toyota ProAce. Made in black ABS plastic. Comes with detailed instructions.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Toyota ProAce Vehicles. This is how you fit your Proclip Car Bracket Mount mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Proclip Car Bracket Mount.



Enlarge image

1. Open the glove compartment. Remove the screw in the upper right corner. Press the thin end of the enclosed gap opener into the gap between the frame surrounding the control panel and the dashboard, to widen the gap. Peel off the cover of the adhesive tape on the Proclip Car Bracket Mount.



Enlarge image

2. Press the curved edge on the right part of the Proclip Car Bracket Mount into the gap below the gap opener. Flip the Proclip Car Bracket Mount forward/leftward so the curved right edge hooks behind the frame surrounding the control panel




Enlarge image

3. Adjust the left part of the Proclip Car Bracket Mount so the hole matches the hole in the dashboard. Screw the Proclip Car Bracket Mount into place with the enclosed screw. Pull out the gap opener. Close the glove compartment.



Enlarge image

4. The Proclip Car Bracket Mount is in place.







Citroen Dispatch for UK
Citroen Jumpy 2nd Gen for UK
Citroen Jumpy III for UK

Fiat Scudo for UK

Peugeot Expert for All Countries

Toyota ProAce for All Countries






Our Price: 15.20 (12.94 ex Vat.)

Item Number: 653972

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: 4

The Proclip Car Bracket Mount is a mounting bracket for the Toyota ProAce's dashboard. Onto the Proclip Car Bracket Mount you can install e.g. a Car Cradle Mount for your mobile phone or PDA or a handsfree set etc. Safe and convenient -always within easy reach. The Proclip Car Bracket Mount is car specific and easy to install. The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the Toyota ProAce. Made in black ABS plastic. Comes with detailed instructions.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Toyota ProAce Vehicles. This is how you fit your Proclip Car Bracket Mount mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Proclip Car Bracket Mount. It is very important to place the Proclip Car Bracket Mount in the exact same position as shown in the pictures.



Enlarge image

1. Press the thin end of the enclosed gap openers into the gap between the frame surrounding the air vent and the coin compartment, to widen the gap. Peel off the adhesive tape covers on the Proclip Car Bracket Mount.



Enlarge image

2. Press the angled edge on the upper part of the Proclip Car Bracket Mount into the gap between the gap openers.




Enlarge image

3. Pull the Proclip Car Bracket Mount downward and press the lower part foward so the angled edge hooks into the gap between the frame surrounding the stereo and the frame surrounding the air vent. Pull out the gap openers.



Enlarge image

4. The Proclip Car Bracket Mount is in place.







Citroen Dispatch for UK
Citroen Jumpy 2nd Gen for UK
Citroen Jumpy III for UK

Fiat Scudo for UK

Peugeot Expert for All Countries

Toyota ProAce for All Countries






Brodit ProClip for Toyota HiAce SLWB Van Angled Car Bracket Mount #653886

Toyota HiAce Australia / Toyota HiAce Commuter Bus Australia / Toyota HiAce SLWB Van Australia

Our Price: 15.51 (13.21 ex Vat.)

Item Number: 653886

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: Brodit Brand New Item - PreOrder Yours NOW !

The Proclip Car Bracket Mount is a mounting bracket for the Toyota HiAce SLWB Van's dashboard. Onto the Proclip Car Bracket Mount you can install e.g. a Car Cradle Mount for your mobile phone or PDA or a handsfree set etc. Safe and convenient -always within easy reach. The Proclip Car Bracket Mount is car specific and easy to install. The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the Toyota HiAce SLWB Van. Made in black ABS plastic. Comes with detailed instructions.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Toyota HiAce SLWB Van Vehicles. This is how you fit your Proclip Car Bracket Mount mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Proclip Car Bracket Mount.



Enlarge image

1. Peel off the adhesive tape covers on the Proclip Car Bracket Mount. Press the thin ends of the enclosed gap openers into the gap between the frame surrounding the air vent and the dashboard, to widen the gap. Hook the angled edge on the lower part of the Proclip Car Bracket Mount into the upper part of the air vent.



Enlarge image

2. Press forward on the upper part of the Proclip Car Bracket Mount so the angled edge on the upper part hooks into the gap between the gap openers.




Enlarge image

3. Press downward on top of the upper part of the Proclip Car Bracket Mount so the angled edge goes all the way into the gap. Pull out the gap openers.



Enlarge image

4. The Proclip Car Bracket Mount is in place.







Toyota HiAce for Australia
Toyota HiAce Commuter Bus for Australia
Toyota HiAce SLWB Van for Australia






Brodit ProClip for Toyota HiAce Commuter Bus Angled Car Bracket Mount #653886

Toyota HiAce Australia / Toyota HiAce Commuter Bus Australia / Toyota HiAce SLWB Van Australia

Our Price: 15.51 (13.21 ex Vat.)

Item Number: 653886

Discounts available for orders of 10 units or more - call +44 1759 371275

Stock: Brodit Brand New Item - PreOrder Yours NOW !

The Proclip Car Bracket Mount is a mounting bracket for the Toyota HiAce Commuter Bus's dashboard. Onto the Proclip Car Bracket Mount you can install e.g. a Car Cradle Mount for your mobile phone or PDA or a handsfree set etc. Safe and convenient -always within easy reach. The Proclip Car Bracket Mount is car specific and easy to install. The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the Toyota HiAce Commuter Bus. Made in black ABS plastic. Comes with detailed instructions.


If you order this product before 4:30pm today, and it is in Stock customers can expect shipment today. If you wish to pre-order or have stock allocated for immediate despatch upon restock please call us or place an order on the website.


These are detailed fitting Instructions for the Brodit Mount for your Toyota HiAce Commuter Bus Vehicles. This is how you fit your Proclip Car Bracket Mount mount onto your Proclip Car Bracket Mount. Full Instructions also come with your mount.

Please read all of the instructions and look at the pictures before attaching the Proclip Car Bracket Mount.



Enlarge image

1. Peel off the adhesive tape covers on the Proclip Car Bracket Mount. Press the thin ends of the enclosed gap openers into the gap between the frame surrounding the air vent and the dashboard, to widen the gap. Hook the angled edge on the lower part of the Proclip Car Bracket Mount into the upper part of the air vent.



Enlarge image

2. Press forward on the upper part of the Proclip Car Bracket Mount so the angled edge on the upper part hooks into the gap between the gap openers.




Enlarge image

3. Press downward on top of the upper part of the Proclip Car Bracket Mount so the angled edge goes all the way into the gap. Pull out the gap openers.



Enlarge image

4. The Proclip Car Bracket Mount is in place.







Toyota HiAce for Australia
Toyota HiAce Commuter Bus for Australia
Toyota HiAce SLWB Van for Australia






 

 



Thank you for adding your Brodit Car Bracket Mount. The Brodit Solution involves Two Steps. If you require a Brodit Car Cradle Mount then please select from the menus below. If you already have a Brodit Car Cradle Mount please proceed to checkout.